6.48 mm diameter nozzle delivering 0.91 l/s to the runner which is rotating at 1084 rpm and generating 225 watts into the grid at an overall efficiency of 47%.

Sunday, 31 December 2017

System efficiency at top-end flows

December has been a better month, - we've had 118 mm of rain, which is double what fell in November and three times what fell in October, - and it's now working its way through for me to see a pleasing uptick in generation.  Units of energy generated in December were 312 kWh (a figure which is poor for December) and the capacity factor for the month was 56%.  At the moment the turbine is putting out 892 W from a flow of 3.26 l/s and these are heights of power and flow which I have never before aspired to.

The explanation behind such an unprecedented level of generation is that I've been waiting for a time when there was copious flow so I could run some tests to check what the system efficiency is at the top end of the range of flows I see at my site. To do this I have had to run the installation a little beyond the limits imposed by the various authorities that licence small hydros: strictly the output should not exceed 750 W and the maximum flow 3 l/s.

Previously in this blog, I presented a plot like the one below to illustrate how operating with one jet in the bottom position was more efficient than operating with both jets:



With the data I had at that time, the plot seemed to show there was a clear advantage to using only one jet and in the bottom position - it gave an improvement in system efficiency of about 2 %, and this advantage seemed to apply throughout the flow range, - although it should be noted that data points for single jet operation are sparse for higher flows, there being only one.

Having copious water available at the moment, it has been possible to get data readings for the larger nozzles very easily, and this has meant I've been able to fill in the gaps in the earlier data series and better define what happens at the top end of the flow range.  The resulting plot, which is based on a completely new data set, now looks slightly different:





... it will be seen that when a very large single jet is employed, one that delivers 3.12 l/s, the efficiency starts to drop off and begins to fall below the trend line for two jet operation.

I'm not sure why this should be. There shouldn't be any question of water from this bigger nozzle missing the cups on the runner: the cups are 70 mm wide and the diameter of the jet 12.2 mm. Maybe it's just that there's a lot of splash from the force of this big jet and that impairs the efficiency.

Some of the reason for the fall-off in efficiency beyond a flow of 2.5 l/s in both single and two jet operation is that shaft speed begins to rise away from the optimum speed for the runner. I have found that with flows greater than 2.5 l/s I have needed to change from the standard Type 2 rotor to the more strongly magnetised Type 2+ rotor. This keeps the shaft speed down to nearer the optimum speed, which for my site is 1000 +/- 100 rpm.  At the moment, generating as I am 892 W from 3.26 l/s, the shaft speed is 1165 rpm.  Were I to push the experimenting and deliver even more water to the runner, the downward trajectory of the efficiency curves for both single and double jet operation would fall off steeply as shaft speed began to rise despite the 'braking effect' of the Type 2+ rotor.

As it happens, I don't want to do such an experiment: the inverter I have is a WindyBoy 1200w and for continuous operation (as is the case when the inverter is coupled to a Powerspout) the output rating of 1200 W has to be down-rated to 900W.  Not wanting to roast the inverter, I think I'll just stay at 892 W.

Saturday, 16 December 2017

Grid failure

This past week has seen snow falling where I live.  However well Western Power, the electricity distribution company for our area, has done its job of cutting back overhanging trees from the power lines, snow always brings problems.  In this past week we have had repeated power outages and I thought it worth writing a Diary entry on how a grid connected Powerspout pelton behaves in such circumstances.  

When the grid goes down, the turbine will continue to receive water and the energy of that water has to have somewhere to go,- where it goes depends on whether it is an older or newer type Powerspout and on what type of inverter is handling the interface between the turbine and the grid.

... the original "grid enabled" Powerspout, the GE 400, which is the one I have, manages the situation by diverting power which cannot pass to the grid whilst the grid is down by sending it to a small heater load which is splash cooled by the spray within the wet side of the turbine casing: 


 Diversion is controlled by an electronic control board, housed in the dry side of the casing, and this regulates the power fed to the heater element so that system voltage is kept at 380 volts DC.



The necessity of keeping voltage at this level is dictated by the inverter I have which is an early one marketed in 2011. It is unable to accept voltages higher than 400v DC.  The electronic control board locks system voltage at 380 v, just below the inverter's limit and thus keeps the inverter from being damaged by over-voltage.

... later, inverters came on the market capable of seeing an in-coming voltage considerably in excess of 400 v: - the 2 kW Enasolar inverter, for example, is quite happy with 600 v.  This development in inverter technology opened the door to managing grid outage situations in a completely different way, a way which was much simpler and did away with the need for a control board.  

Instead of diverting electrical power to a load, electrical power ceases to be created at all by keeping the system in open circuit: with no load connected what happens is that system voltage rises as the pelton runner goes to its run-away speed but, crucially, no current flows.  And so long as the system voltage rises to no more than 600 v the inverter remains safe.  What becomes important with this way of managing grid outages is that a stator must be selected which is wound in such a way that even at the highest run-away speed possible for the site (which is determined by the net head), the open circuit voltage will never exceed the inverter's limit.

You may well ask "but what happens to all the hydraulic energy in the system if none of it now finds an outlet by being turned into electrical energy?" The answer is that a lot of it never gets as far as being translated into shaft rotational energy. At the run-away speed of the pelton much of the water passes through the pelton runner, which is moving just about as fast as the water jet, without ever hitting the pelton cups.  The water ends up hitting the casing opposite the nozzle and its energy is dissipated as heat and sound. Some extra energy is also lost as heat in the bearings and shaft seal - a greater amount at the higher speed at which the shaft is revolving at run-away speed than is lost at normal operating rpm.

To illustrate some of this, here is a picture of a pelton at run-away speed showing how the water from both nozzles fails to be deflected in the normal way onto the front glazing because the velocities of both runner and jets are little different:


This pelton was coupled to an Enasolar 2 kw inverter which, at the time, was not connected to the grid; the run-away speed of the turbine which resulted was measured at 1440 rpm:



and because the stator of the SmartDrive had been carefully selected to be one which delivered just 0.266v /rpm in open circuit (it was a 100-14S-1P S stator), the open circuit voltage at runaway was measured at 383 v: well below the 600 v limit of the inverter.

So there have been two ways of managing a grid outage with a Powerspout pelton and both are good.  This past week with its numerous grid outages has reminded me just how "bomb proof" my system is: when the grid goes down, the turbine continues happily feeding power to its dump load and after the grid comes back on, seamlessly the turbine re-connects itself to the grid.  It's all clever stuff and it gives me great pleasure to see it in operation.

Monday, 7 August 2017

Peltons past and present.

I've recently acquired a new pelton wheel, - only it isn't new, - it was made in 1905 by an engineer who, at that time of his life, lived and worked from a small town about 40 miles from here. His name was Percy Pitman and here is an article he wrote for the October edition of 'The Engineer' in 1905. I guess it's probably him in the picture:











It's worth remembering that 1905 was only 25 years after Lester Pelton, living in Ohio, USA, filed his patent for an impulse turbine having cups with a splitter ridge, so the cups effectively became two cups side by side. Prior to this, cups were more like a single bucket and the water entering them had to bounce back rather than be streamed outwards to each side.  Pelton's design made the wheel significantly more efficient.

The wheel which has come to me was for sale in a farm auction.  Where I live, when a farmer retires, it is usual for him to have a sale of his old equipment, - everything from tractors to scrap wood and steel. The farmer who was retiring had bought this pelton at a similar farm auction some years before, but had never done anything with it. By the look of it, the lack of wear on the buckets indicated it had NEVER done any real work:




Back home, shot-blasted, painted and mounted on a frame which I picked up from another farm auction, the wheel is beginning to look presentable.  I'm intending to put it close to my Powerspout so people passing can understand what a pelton wheel is.  I'm amazed at how many people have never heard of the word !  Here's how it looks now with a Powerspout pelton next to it to give an idea of size:





Life sometimes throws up odd coincidences !  A few weeks after getting my pelton, a friend drew my attention to an advertisement for the sale of ANOTHER pelton wheel, almost certainly by Percy Pitman because of having identical construction and being located in the vicinity of Bosbury where he lived, but this time a more complete example than mine:






To have TWO historic pelton wheels become available within weeks of each other is a truly unusual event.  And to learn that one hundred years ago, in this part of Wales, there was a man making his name by the manufacture of such wheels gives a nice historical dimension to my Powerspout operating today.  

There's one curiosity that remains with me though: - my pelton is NOT well made; the cups are steel castings bolted to a circular steel plate, but they have not been attached around the circumference in a way that makes them equi-distant from each other, - at one side they are crowded together and at the opposite side spaced more apart.  The effect is that the wheel is badly un-balanced and a rather crude effort was made to balance it by bolting on a strip of steel. I have removed it because it was rusting badly and the rust was eating into the circular steel plate, but where it was attached can just be seen by the presence of two bolt holes at the wheel's 12 o'clock position.

Perhaps Percy Pitman was not the meticulous engineer he advertised himself to be ! Certainly he quickly left behind the manufacture of 'industrial' pelton wheels to pursue the manufacture of "hydraulic equipment for educational establishments".  But judging by the progressively more prosperous houses he occupied in London he must have died a well-to-do gentleman and a far cry from his humble beginnings in Bosbury, Herefordshire where he started out.

Postscript added Nov 2019:
More about Percy Pitman can be found here.

How the finished wheel looks: